PCR-LE Series
よくあるご質問 閲覧ランキング
- 耐電圧(耐圧)試験って何ですか?
- 直流電源を接続する配電盤のブレーカ選定について教えてください。
- 検査票、試験成績書、校正証明書、トレーサビリティ証明書について教えてください。
- 電波法の高周波利用設備に該当する製品はありますか。
- VISAライブラリについて教えてください。
- ウォームアップ時間はどれくらいですか。
- 製品に電安法適用表示(PSEマーク)がありません。違法ではないですか。
- 耐電圧試験器を操作するために、必要な資格はありますか。
- PWR-01シリーズのPOWER スイッチをオンにしても動作しません。どうしたら良いでしょうか。
- 製品におけるPCB含有の有無について教えてください。
- マニュアル通りにコマンドを送っているのですが動作しません。どうしたらよいでしょうか。
- Can the output voltage and current be monitored when multiple units of PCR-LE series are used?
- Is it possible to ground either the L or N terminal of the single-phase two-wire output of PCR-LE series?
- Can PCR-LE2 series and the optional SD012-PCR-LE/WE (avionics test software) be used to simulate power line abnormalities?
- Can the output voltage and output on/off of PCR-LE series be controlled externally?
- Can PCR-LE series operate in constant current (CC) mode?
- I sent the command of “FETC:CURR?” via the programmable logic controller (PLC) to PCR-LE series, but I received no response. How can I retrieve the measured value?
- Is it possible to obtain a PDF version of the communication interface manual for PCR-LE series?
- Why cannot I connect a PC with the optional SD009-PCR-LE/WE (power line disturbance immunity testing software) to PCR-LE series via an RS232C interface?
- Can PCR-LE series be used as a substitute for an isolation transformer?
- Can I set unlimited repetitions of the loop for the sequence function on PCR-LE series?
- After configuring a single-phase three-wire output using the optional 2P05-PCR-LE (single-phase three-wire output driver) for PCR-LE series, is it necessary to adjust the phase once the power is turned on?
- In PCR-LE series, how do I set the output voltage to 230 V between the L and N terminals, 0 V between N and G terminals, and 230 V between L and G terminals?
- I have set the sequence settings of PCR-LE series as follows: the output voltage is set to 200 V and the voltage range is set to L. If I change the sequence setting to the H range, can PCR-LE series output 0 V?
- Why does the error code +202 “Operation denied” appear when executing a sequence in PCR-LE series?
- PCR-LE series can output a negative voltage controlled by a rotary knob. Can I set the negative voltage not to output?
- Is it possible to use one of the phase from a three-phase power distribution system as an input for the single-phase two-wire input model of PCR-LE series?
- Is it possible to import or export arbitrary waveforms created on the optional SD011-PCR-LE (sequence creation software Wavy) to PCR-LE series?
- Where can I find the description in the user’s manual regarding how to set the short interruption setting on a three-phase output in PCR-LE series?
- Is it possible to conduct an IEC61000-4-11 compliance test using the power line abnormality simulation function of PCR-LE series through panel operation?
- Is it possible to conduct a 1-millisecond short interruption test through panel operation of PCR-LE series?
- Why does TRBL-25 occur on PCR-LE series?
- Does PCR-LE series require a setting to switch an AC power line voltage between 100 V and 200 V?
- Can two units of PCR-LE series be synchronized?
- The output voltage modes of PCR-LE series include AC, DC, and AC+DC modes. How is the output terminal block is marked?
- What is the isolation voltage (AC line-to-ground) for PCR-LE series?





